Presented here in the next paragraph you can get lots of dependable resources about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably hard job. If the old bathtub is conveniently easily accessible, the project can move rapidly; if you need to open a wall surface to eliminate the old bathtub and place the brand-new tub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the task and fit attempting it. Rather than hiring a professional to take control of a halfway-completed job, it is better to consider employing one before you start. Opportunities are you may require an expert plumber to make tube links.
This write-up will assist you set up a brand-new bath tub in your restroom if you have already purchased a brand-new tub as well as do not need to alter the arrangement of your previous water system pipes.
Your devices and material list must comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the restricted access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before going on to fit the brand-new faucets, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in area between the tap and also the sink. Safeguard the faucet in position with the producer offered backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The former kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bath tub
Using the two wood boards under its feet, put the bath tub in the called for position. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the bath tub until the level reviews degree.
To install faucets, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Activate the water supply as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as additionally check the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bath tub ought to wait until the bathtub has actually been used at least when as this will certainly resolve it into its final position.
Preparing for the Installment
To start with, the supporting frame supplied with the bath ought to be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final position.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bath and the tiling, bring about issues with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components as well as installations. They are offered in tubes and also cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the bath tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly offered on the market. It is recommended to fit the tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very enthusiastic about How to Install a Bathtub and I really hope you enjoyed reading our piece. Those who enjoyed reading our post plz be sure to share it. I value reading our article about How to Install a Bathtub.
Real results? Dial!